Required door thickness (in.) Strike plate height (in.) Strike plate width (in.) Holding force (lb.) Product Weight (lb.) Faceplate depth (in.) Faceplate height (in.) Faceplate width (in.) Projection (in.) Required door thickness. Defiant has roughly the same machining tolerance as Kwikset and they also have bottom pins that are rounded on both ends. But, because Defiant locks include at least one spool-shaped top pin, they get two stars. Defiant can be made more secure by using after-market bottom pins (Lab is a major supplier) that are flat on the top.
121
![Instructions Instructions](https://mobileimages.lowes.com/product/converted/043156/043156168286.jpg)
Choose a position on the door for the lock.
Install the deadbolt lock about 44 inches above the bottom of the door. You’ll have to adjust the position a bit if you have a combination storm door so as not to interfere with the storm doorknob or lock.
221
Affix the template to the door.
Use masking tape to affix the template at the proper position.
321
Mark the center of the holes for both the lock cylinder and latchbolt.
Use a sharp point to mark the centers of the two hole positions for the lock cylinder (through the face of the door) and the latchbolt (into the edge of the door).
421
Mark the center of the holes for both the lock cylinder and latchbolt.
Use a sharp point to mark the centers of the two hole positions for the lock cylinder (through the face of the door) and the latchbolt (into the edge of the door).
521
Bore the hole for the lock cylinder.
Some kits include a hole saw that attaches to a standard drill. Align the center pilot bit of the saw with the marked point of the face of the door and drill through.
621
Drill the latchbolt hole into the edge of the door
Use a 1-inch spade bit attached to your drill to cut a perfectly round hole into the wood.
721
Cut a latchbolt mortise in the edge of the door.
Use a sharp 1-inch chisel and a hammer to cut a recess that is 1/8 inch deep.
821
Cut a latchbolt mortise in the edge of the door.
Use a sharp 1-inch chisel and a hammer to cut a recess that is 1/8 inch deep.
921
Position the latchbolt faceplate flush with the edge of the door.
Remove any wood chips with the chisel blade until the faceplate is flush.
1021
Install the two mounting screws into the faceplate.
Hold the faceplate in place and use it as a template for installing the two mounting screws.
1121
Apply a coating of lubricant to the lock's moving parts.
Spray a thin coating of lubricant to all the moving parts of the lock.
1221
Apply a coating of lubricant to the lock's moving parts.
Spray a thin coating of lubricant to all the moving parts of the lock.
1321
Insert the latchbolt and push the keyed portion of the lock through the hole in the latchbolt.
Place the latchbolt in its hole and insert the keyed portion of the lock so that the tailpiece extends through the hole in the latchbolt.
1421
Fit the inside cylinder so that the holes for the screws line up with the exterior side.
From the inside of the door, adjust the inside cylinder to line up the screw holes with the exterior portion of the lock.
1521
Secure the two sides of the lock together.
Use the two retaining screws to hold the lock in place.
1621
Secure the two sides of the lock together.
Use the two retaining screws to hold the lock in place.
1721
Shut the door and mark the doorjamb where the latchbolt touches.
Use a pencil to mark the spot on the doorjamb where the latchbolt meets the jamb.
![Defiant Defiant](/uploads/1/2/6/5/126513664/281633599.jpg)
1821
Trace and cut a mortise on the doorjamb for the strike plate.
Use the strike plate as a template and then trace and cut a mortise on the doorjamb with a sharp chisel.
1921
Bore a latchbolt hole in the center of the mortise.
Use a spade bit to bore a hole in the center of the strike plate mortise for the latchbolt to enter.
2021
Install the strike plate.
Install the strike plate using the screws provided.
2121
Close the door and test the lock.
Shut the door and test the fit by operating the deadbolt lock. If necessary, loosen the screws and adjust the lock until the latchbolt passes easily into its hole.
This topic contains 1 reply, has 2 voices, and was last updated by 11 months ago.
- Here is working link http://fmr.press/file-198438-zip.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Here is working link http://fmr.press/file-198438-zip.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Here is working link http://fmr.press/file-198438-zip.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Here is working link http://fmr.press/file-198438-zip.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Here is working link http://fmr.press/file-198438-zip.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Here is working link http://fmr.press/file-198438-zip.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.